Confirm to proceed" box and select continue to start the process. Check the "All target volume data will be overwritten. You get another option to cancel the process. You should close all other programs now and save all work before you continue. The program warns you that all data on the target disk will be overwritten in the process. You may also select cancel to postpone it. Just select "ok" on the screen to start the cloning right away. Macrium Reflect Free displays a "what do you want to do now" prompt next. Select the finish button to complete the configuration. There you find information about the cloning and each of the partitions that the backup app will copy in the process to the new drive. Macrium Reflect Free displays an overview on the final screen. Since this is a one-time operation, there is no need to schedule the task so that it can be executed again in the future. Select next to proceed and then next again to skip the scheduling part. The two disks do not need the same amount of space, but there needs to be enough free space available. Note that you need sufficient space on the new disk so that all data that is on the source disk can be copied. You should see an exact copy of the disk structure after the selection. Once done, select the copy partitions button and then "exact partition offset and length" from the selection menu. Since you want to copy the system disk, you need to make sure that the entire disk is free. Use the "delete partition" action to remove any existing partition from the second disk. Activate "select a disk to clone" to pick the destination drive. The clone window opens and the main disk is displayed at the top as the source disk. Select "clone this disk", which you find under the main system disk in the interface. Macrium Reflect Free displays all disks and their partitions in its interface. One thing that you need to do is connect both hard drives to the PC as you will copy data from the running system disk to the new disk. Note: you may want to decrypt an encrypted partition before you start the process, as the encryption software may not play nicely because of the changed disk. You may also download the software from third-party sites such as Softonic. You can do so from the developer website, but need to supply an email address to do so. This guide uses a free disk backup software, Macrium Reflect Free to be precise, to clone the system partition of the slow SSD to the fast SSD.įirst thing you need to do is download Macrium Reflect Free. While there are many guides on cloning available on the Internet, most appear to advertise paid products. Since I did not want to reinstall Windows or apps, I decided to clone the disk as this would speed things up significantly. Cloning copies all data from one disk to another. I had a good 256 Gigabyte Solid State Drive still lying around from an old PC and decided to replace the slow SSD of the new PC with the fast SSD of the old. It had a good amount of space, 512 Gigabytes, but as soon as write processes would start, it would slow down things on the entire system considerably. With that dump you are sure, that you did not miss any important metadata (like ACLs) which tar won't capture.I bought a new Windows 11 PC this week for Office work and noticed that the Solid State Drive was slowing things down. Do that with other partitions on the failing drive, too. Where you had to adopt /dev/sda1 to the right device. However, you should (also) consider to make a dd dump of the failing drive's partitions: cd good_partition netcat -l -p 1234 > dd if=/dev/sda1 | netcat good_host.ip 1234 (especially the file representing your RAM in ( /proc/kcore) will add an unnecessary amount of data). I included some -exclude parameters, as /proc and /sys are virtual filesystems and hence useless on the new host. The bad host sends the data to this port, also using tar and netcat. Which opens a listening port 1234 on the good machine netcat -l -p 1234 and pipes the incoming data to tar to extract (preserving mtime and permissions). cd good_partition netcat -l -p 1234 | tar xvpmf tar -cv -f-exclude=/proc -exclude=/sys / | netcat good_host.ip 1234 This is usually much faster as it doesn't encrypt the data. If both computers are on the same (safe) LAN, I recommend a different approach using netcat.
0 Comments
Leave a Reply. |
Details
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |